E806/6NHD
Highbay with triangular design.
CRI 90
Most of our products are also available in CRI (Ra) 90.
LLMF
The figure that reflects the drop in luminous flux of the light source (LLMF) takes into account failing LEDs, and deterioration of the light output over time. How do we determine this LLMF? We distinguish between the service life of LEDs at the component level and at the luminaire level.
At the component level we take into account the gradual deterioration of the luminous flux of the LEDs (parametric failure or B-lifetime), and the potential breakdown of LEDs (catastrophic failure or C-lifetime). At the luminaire level the complete failure of a luminaire is not relevant (see Luminaire Survival Factor). The LLMF corresponds with the B-lifetime at the luminaire level and hence takes on board the parametric as well as catastrophic failure of the individual LEDs in the luminaires.
In order to achieve an accurate, reliable LLMF for our luminaires, we carry out a ‘principal component analysis’:
- We determine the parametric failure at the component level in accordance with objective LM80/TM21.
- We are unable to calculate the catastrophic failure, but prefer to collaborate with manufacturers who make accurate data available. Whenever no measurement data are offered, we depend on electronic reliability models (MIL-HBK-217F)
UGR
Unified Glare Rating
This is an approximate model expressing the risk of glare.
The standard values range from UGR 16 (low risk of glare) to UGR 28.
In the standard for workplace lighting EN12464-1, limit values for UGR are imposed for various rooms.
Quick downloads
Photometric data
- DIALux ULD
- Eulumdat LDT
Tender description
- Tender description
- Tender description with picture
Product description
Product data sheet
Tender description
Product Info
Mechanical properties
Electrical Properties
Power factor
The power factor is a technical indicator of the driver that shows how closely the current of the waveform approximates the sinusoidal reference of the voltage. The power factor (λ) is composed of two parts:
the shift between voltage and current (cos ϕ) and the distortion of the current (harmonics or Total Harmonic Distortion).
The smaller the shift and distortion of the waveform, the fewer losses and pollution on the energy supplier’s distribution network. In ETAP LED drivers we exclusively work with a power factor in excess of 0.9.
Autonomy
When the mains power supply fails, the emergency lighting will come on for a certain period of time: the duration
- 60 minutes: suitable for many applications
- 180 minutes: Most common requirement for the UK. When the evacuation requires more time, for example in high-rise buildings or care centers
Circularity Index
Circularity index
The circularity index indicates the level of circularity and sustainability achieved by our luminaires.
- The product circularity score indicates how well our product fits into the circular economy based on our endless, effortless and wasteless principles.
- The lifetime efficiency score compares the energy and material impact of our luminaire with a reference product in the market.
Through the circularity index, we challenge ourselves to continuously enhance our products and achieve higher scores in terms of circularity and sustainability.
Eprel Data Lightsource
Lifetime
| Time(hrs) | LLMF(%) | Cx(%) |
|---|---|---|
| 10000 | 98 | 1 |
| 20000 | 96 | 2 |
| 30000 | 94 | 3 |
| 40000 | 92 | 4 |
| 50000 | 90 | 5 |
| 60000 | 88 | 6 |
| 70000 | 86* | 7 |
| 80000 | 85* | 8 |
| 90000 | 83* | 9 |
| 100000 | 81* | 9 |
Dimensional sketch
Photometric data
References
Videos
Downloads
Suspension set
Mounting brackets for surface mounted mounting
Two carabine hooks
Fixed wall mounting under 30° - Two brackets
